1. Tarken installation

Open the window by turning the
window handle to the 90° position and pulling the handle towards you. Once the window is open, proceed to turn while slightly pulling the screw cover to make the screws accessible

Remove the window handle by
unscrewing both screws in a counter
clockwise direction. Keep the screws, since those will be needed later during the assembly of the Tarken device.

Use your thumb to open the front cover
by applying slight force on the button
while directing it outwards.
The front cover should open up after which it can
be easily removed by pulling it outwards.

Attach the Tarken device to the
window. The device has a square spindel
on the back side, which must be inserted
into the square hole in the window.
Make sure during the attachment, that the
screw holes on the Tarken device are
aligned with the screw holes on the
window. The back side of the device
should be touching the window panel.

Insert the same two screws that were
removed before into the screw tunnels
as shown. Proceed to screw
both screws in by screwing in a
clockwise direction. Do not use excessive force when tightening the screws.

Attach the front cover back to the
device by placing the hinges to their
corresponding slots and turning the
cover inwards until the cover locks.

NB! Use provided cleaning wipe to clean the window surface where the anchor is applied.

Remove the sticker cover foil from the wall anchor (Do not remove the sticker).

Keep the wall anchor aligned with the
Tarken device while slowly closing the window. Once the anchor touches the wall, apply pressure to make sure the sticker glue holds. Let the glue cure for 15 minutes before using the device.

2. Using Tarken

The Tarken device has a vertical slider button on the front surface. Moving the slider to any postion will wake up the device on and pairing mode is activated. Blue LED will be blinking for 1 minute.

After the blinking has ended the device is in active state. Active state should be used only when device is properly mounted to window.

  • Sliding the button to position 1 will open the window
  • Sliding the button to position 2 will release the window
  • Sliding the button to position 3 will close the window

Moving the button rapidly to position 1-3-1 or 3-1-3 will shut down the device. This will be indicated by three consecutive red LED blinks.

The Tarken automatically detects the device orientation, position 1 remains the upper position regardless.

When releasing window, wait until the device has unlocked the window and proceed to press the button on top of the window anchor to disengage the device and open window completely.

To engage the device again hold down the button on window anchor and gently close the window. Release the button and verify that the anchor is attached to device. Proceed to open or close the window

3. Using mobile application

To pair Tarken device with the mobile application activate the pairing mode on device by moving the slider. If device is already active shut it down first by moving slider rapidly between positions 1-3-1 or 3-1-3.

When the blue LED is blinking go to settings menu (gear icon on top left corner) on the app and choose "scan for devices". Choose available Tarken device for pairing.

  1. Settings
  2. Release window
  3. Reconnect to last device - only visible when in not connected state
  4. Window status indicator
  5. Open/close commands (for manual mode only)
  6. Battery level indicator
  7. Air quality indicator
  8. Mode selector
  9. Current humidity
  10. Current temperature
  11. Connected status indicator
  12. Device selector

  1. Scan for available devices - used to pair new Tarken device
  2. Allow permissions
  3. Clear paired devices
  4. Rename device - renames device that is currently connected
  5. Manual movements for spindle
  6. Manual movements for linear actuator
  7. Fully or partially open slider. Partially open mode opens the window only slightly
  8. Disconnect for current device

  1. Temperature automation block
  2. Air quality automation block
  3. Humitity automation block
  4. Current reading
  5. Set point
  6. Block activated/deactivated slider
  7. Set point slider
  8. Window position indicator - click to switch
  9. Priority switch - in case of conflicting conditions, condition with priority will be used
  10. Action to be done - click to switch
  11. Set timer
  12. Save settings - click to activate mode with selected settings